Pristine and cobalt doped copper sulfide microsphere particles for seawater splitting

In this work, copper sulfide particles are synthesized with different Co doping concentrations such as 0, 1 and 5% at 80 °C by optimizing synthesis times from 1 to 3 h. Copper sulfide particles possess two structural phases of covellite CuS and digenite Cu₉S₅. The increase in synthesis time from 1 to 3 h increases the Cu₉S₅ phase growth and changes the morphology from flower to microsphere. The CuS synthesized with 0, 1 and 5% Co dopant concentrations demonstrate flower consisting of agglomerated nanosheets, microsphere and flower like microsphere. The elemental investigation substantiates Co ions presence in CuS microspheres. The A_1g (LO) mode intensity is decreased with increase in Co dopant concentration confirming Co incorporation into CuS microsphere. The CuS synthesized with 0, 1, 5% Co dopants exhibit 322 mV, 305 mV and 289 mV to attain 100 mA/cm² in 1 M KOH seawater. The CuS synthesized with 5% Co dopant demonstrates higher double layer capacitance (C_dl) of 173.9 mFcm^?2 and lower charge transfer resistance (R_ct) of 6.07 Ω with 78.84% retention after 10 h continuous stability than that of the other pristine (118.3 mFcm^?2, 13.72 Ω) and 1% Co doped CuS microsphere (165.7 mFcm^?2, 8.55 Ω) indicating more surface active site and rapid charge carrier transport, respectively.     

A dotted nanowire arrayed by 5 nm sized palladium and nickel composite nanopaticles showing significant electrocatalytic activity towards ethanol oxidation reaction (EOR)

To the best of our knowledge, this is the first time to report the preparation of a dotted nanowire arrayed by 5 nm sized palladium and nickel composite nanoparticles (denoted as Pd_xNi_y NPs) via a hydrothermal method using NU and PdO·H₂O as the starting materials. The samples prepared at the mass ratio of NU to PdO·H₂O 1:1, 1:2 and 2:1 were, respectively, nominated as catalyst c₁, c₂ and c₃. The chemical compositions of all synthesized catalysts were mainly studied by using X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS), revealing that metallic Ni was one main component of all prepared catalysts. Surprisingly, the main diffraction peaks appearing in the XRD patterns of all prepared catalysts were assigned to the metallic Ni rather than the metallic Pd. Very interestingly, as indicated by the TEM images, a large number of dotted nanowires arrayed by numerous equidistant 5 nm sized nanoparticles were distinctly exhibited in catalyst c₁. More importantly, when being used as electrocatalysts for EOR, all prepared catalysts exhibited an evident electrocatalytic activity towards EOR. In the cyclic voltammetry (CV) test, the peak current density of the forward peak of EOR on catalyst c₁ measured at 50 mV s^?1 was as high as 56.1 mA cm^?2, being almost 9 times higher than that of EOR on catalyst c₃ (6.3 mA cm^?2). Particularly, the polarized current density of EOR on catalyst c₁ at 3600 s, as indicated by the chronoamperometry (CA) experiment, was still maintained to be around 1.47 mA cm^?2, a value higher than the latest reported data of 1.3 mA cm^?2 (measured on the pure Pd/C electrode). Presenting a novel method to prepare dotted nanowires arranged by 5 nm sized nanoparticles and showing the significant eletrocatalytic activities of the newly prepared dotted nanowires towards EOR were the major contributions of this preliminary work.     

Uniform cobalt grafted on vanadium nitride as a high efficient oxygen evolution reaction catalyst

The rational design of highly effective and low-cost catalysts for oxygen evolution reaction (OER) is of prime importance for the development of water splitting. However, the activity of electrocatalysts still needs enhancement to satisfy the practical application. Herein, we report Co nanoparticles grafted on vanadium nitride (VN) surface via in situ phase separation method by nitriding Co₂V₂O₇ precursor. Benefiting the advantages of abundant active sites of Co, high conductivity and corrosion resistance of VN, the Co/VN achieves incredibly high activity and durability for OER with a low overpotential of 320 mV at a current density of 10 mV cm^?2 with a small Tafel slope of 50.4 mV dec^?1 and long-term stability. In addition, the in situ Raman further reveals the synergistic effect of Co and VN. Significantly, this study may enrich our knowledge and it can be extended to prepare other interconnected framework structures for the development of OER catalysts.     

梁结构振动支承约束反力控制

支承或连接构件对梁结构的动力学性能有至关重要影响,必须保证其在振动过程中不发生破坏或者失效。通过合理设计和布局附加弹性支承可以实现对这些重要连接构件所承受约束反力的控制。应用微分变换法推导含附加支承的梁结构支承约束反力及其对于附加支承位置和刚度的灵敏度表达式,并通过优化设计附加支承位置和刚度实现具有弹性约束端的简支梁结构各支承约束反力的平衡,可提高结构的动力学性能。     

Oxidation State Modulation of Bismuth for Efficient Electrocatalytic Nitrogen Reduction to Ammonia

Electrocatalytic nitrogen reduction reaction (NRR) is a promising strategy for ammonia (NH₃) production under ambient conditions. However, it is severely impeded by the challenging activation of the NN bond and the competing hydrogen evolution reaction (HER), which makes it crucial to design electrocatalysts rationally for efficient NRR. Herein, the rational design of bismuth (Bi) nanoparticles with different oxidation states embedded in carbon nanosheets (Bi@C) as efficient NRR electrocatalysts is reported. The NRR performance of Bi@C improves with the increase of Bi⁰/Bi³⁺ atomic ratios, indicating that the oxidation state of Bi plays a significant role in electrochemical ammonia synthesis. As a result, the Bi@C nanosheets annealed at 900  ° C with the optimal oxidation state of Bi demonstrate the best NRR performance with a high NH₃ yield rate and remarkable Faradaic efficiency of 15.10  ± 0.43% at − 0.4 V versus RHE. Density functional theory calculations reveal that the effective modulation of the oxidation state of Bi can tune the p-filling of active Bi sites and strengthen adsorption of *NNH, which boost the potential-determining step and facilitate the electrocatalytic NRR under ambient conditions. This work may offer valuable insights into the rational material design by modulating oxidation states for efficient electrocatalysis.     

Modulation of electrical transport in calcium cobaltite ceramics and thick films through microstructure control and doping

Ca₃Co₄O₉ is a promising p-type thermoelectric oxide material having intrinsically low thermal conductivity. With low cost and opportunities for automatic large scale production, thick film technologies offer considerable potential for a new generation of micro-sized thermoelectric coolers or generators. Here, based on the chemical composition optimized by traditional solid state reaction for bulk samples, we present a viable approach to modulating the electrical transport properties of screen-printed calcium cobaltite thick films through control of the microstructural evolution by optimized heat-treatment. XRD and TEM analysis confirmed the formation of high-quality calcium cobaltite grains. By creating 2.0 at% cobalt deficiency in Ca_2.7Bi_0.3Co₄O_9+δ, the pressureless sintered ceramics reached the highest power factor of 98.0 μWm^?1 K^-2 at 823 K, through enhancement of electrical conductivity by reduction of poorly conducting secondary phases. Subsequently, textured thick films of Ca_2.7Bi_0.3Co_3.92O_9+δ were efficiently tailored by controlling the sintering temperature and holding time. Optimized Ca_2.7Bi_0.3Co_3.92O_9+δ thick films sintered at 1203 K for 8 h exhibited the maximum power factor of 55.5 μWm^?1 K^-2 at 673 K through microstructure control.     

Core–Shell Photoanodes for Photoelectrochemical Water Oxidation

Photoelectrochemical (PEC) water splitting into hydrogen and oxygen is a promising solution for the conversion and storage of solar energy. Because sluggish water oxidation is the bottleneck of water splitting, the design and preparation of an efficient photoanode is intensively investigated. Currently, all known photoanode materials suffer from at least one of the following drawbacks: ① low carriers separation efficiency; ② sluggish surface water oxidation reaction; ③ poor long-term stability; ④ insufficient water adsorption and gas desorption. Core–shell configurations can endow a photoanode with improved activity and stability by coating an overlayer that plays energetic, catalytic, and/or protective roles. The construction strategy has an important effect on the activity of a core–shell photoanode. Nonetheless, the mechanism for the improvement of performance is still ambiguous and is worthy of a closer examination. In this review, the successes and challenges of core–shell photoanodes for water oxidation, focusing on synthesis strategies as well as functionalities (facilitating carrier separation, surface reaction promotion, corrosion prevention, and bubble detachment) are explored. Finally, the perspectives of this class of materials in terms of new opportunities and efforts are discussed.     

CNT-interconnected iron-doped NiP2/Ni2P heterostructural nanoflowers as high-efficiency electrocatalyst for oxygen evolution reaction

Oxygen evolution reaction (OER) plays a decisive role in electrolytic water splitting. However, it is still challengeable to develop low-cost and efficient OER electrocatalysts. Herein, we present a combination strategy via heteroatom doping, hetero-interface engineering and introducing conductive skeleton to synthesize a hybrid OER catalyst of CNT-interconnected iron-doped NiP₂/Ni₂P (Fe-(NiP₂/Ni₂P)@CNT) heterostructural nanoflowers by a simple hydrothermal reaction and subsequent phosphorization process. The optimized Fe-(NiP₂/Ni₂P)@CNT catalyst delivers an ultralow Tafel slope of 46.1 mV dec^?1 and overpotential of 254 mV to obtain 10 mA cm^?2, which are even better than those of commercial OER catalyst RuO₂. The excellent OER performance is mainly attributed to its unique nanoarchitecture and the synergistic effects: the nanoflowers constructed by a 2D-like nanosheets guarantee large specific area and abundant active sites; the highly conductive CNT skeleton and the electronic modulation by the heterostructural NiP₂/Ni₂P interface and the hetero-atom doping can improve the catalytic activity; porous nanostructure benefits electrolyte penetration and gas release; most importantly, the rough surface and rich defects caused by phosphorization process can further enhance the OER performance. This work provides a deep insight to boost catalytic performance by heteroatom doping and interface engineering for water splitting.     

Effect of heat treatment on the synthesis of hydroxyapatite from Indian clam seashell by hydrothermal method

Hydroxyapatite (HA) powder has been successfully synthesized from low-cost Indian clam seashells by using hydrothermal method. The mixture of tri-calcium phosphate [Ca₃(PO₄)₂], heat-treated ball-milled clam seashell, and demineralized water are heat-treated at several temperatures (700 °C, 800 °C, 900 °C, 1000 °C, and 1100 °C) for various time periods (1 h, 2 h, and 3 h) to perform the hydrothermal reactions. The phases and microstructure of the solid-state reaction products are analyzed through X-ray diffraction (XRD) method and field emission scanning electron microscopy (FESEM) respectively. The crystallite size of all the synthesized powders is calculated by using Scherrer's model. Mainly HA phase is obtained in all the different reaction products. However, these HAs are found to be non-stoichiometric in nature. As per the literature, non-stoichiometric HA is a more biologically active material compared to the stoichiometric one. Almost pure HA is formed with any selected reaction temperature applied for 2 h time duration. The crystallinity and Ca/P ratio of the synthesized pure HA are estimated by using standard model and energy-dispersive X-ray spectroscopy (EDS) analysis, respectively. The highest amount of near stoichiometric crystalline HA has been obtained at 900 °C of reaction temperature applied for 2 h time duration. With raising reaction temperature, the grain size of pure HA is found to be increased. Needle/rod shaped nano grains are noticed to form at lower reaction temperature whereas; beyond 1000 ^oC of temperature globular/spherical shaped grains are also observed to form. At 3 h reaction time agglomeration of grains is found to occur in all the synthesized powders.